hp dl388 install linux 无法识别raid,HP Proliant DL580 G5安装centos7 x64无法识别阵列卡问题...

hp dl388 install linux 无法识别raid,HP Proliant DL580 G5安装centos7 x64无法识别阵列卡问题...

1、进入安装光盘，用上下键选择安装centos——Install Centos7(注意不可按Enter键)，如图：

2、按Tab键，对安装进行额外配置，在屏幕最下方会显示如下字样：

3、在额外配置的命令行上添加配置： hpsa.hpsa_simple_mode=1 hpsa.hpsa_allow_any=1，如图所示：

4、按回车继续安装

经过以上几步，安装程序即可识别出HP服务器的硬盘。

参考：

.php?f=49&t=47011

So the HP RAID controller driver from around 2001 to ~2009 was the CCISS driver. There was a transition to the HPSA driver at some point, moving the Smart Array controller support back into the regular SCSI subsystem versus the dedicated

HP servers from the G1 to G5 era used the CCISS driver. On newer operating systems (EL6 and forward), HP ProLiant G6 and newer systems made use of the HPSA driver.

It turns out that RHEL7 removes the old CCISS module. Your fix in this case, since the Smart Array P400 controller in your G5 server isn't recognized, is to force the HPSA driver to load your older controller. Do this with:

hpsa.hpsa_allow_any=1

As a

From the man page.

hpsa_allow_any=1: This option allows the driver to attempt to operate on any HP Smart Array hardware RAID controller, even if it is not explicitly known to the driver. This allows newer hardware to work with older drivers. Typically this is used to allow installation of operating systems from media that predates the RAID controller, though it may also be used to enable hpsa to drive older controllers that would normally be handled by the cciss(4) driver. These older boards have not been tested and are not supported with hpsa, and cciss(4) should still be used for these.

EDIT

This is a much more involved process than expected. You need to add that string to the module load parameters.

The official word is that the older controllers are just no longer supported. While you can get it running, it's less-than-ideal. So I'd probably stay away from EL7 for now. There will likely be a workaround, since there's an existing install base of

⁠kernel component, BZ#1061210 When the hpsa_allow_any option is used, the hpsa driver allows the use of PCI IDs that are not listed in the driver's pci-id table. Thus, cards detected when this option is used, are not supported in Red Hat Enterprise Linux 7.

⁠kernel component, BZ#975791

The following cciss controllers are no longer supported:

◦ Smart Array 5300

◦ Smart Array 5i

◦ Smart Array 532

◦ Smart Array 5312

◦ Smart Array 641

◦ Smart Array 642

◦ Smart Array 6400

◦ Smart Array 6400 EM

◦ Smart Array 6i

◦ Smart Array P600

◦ Smart Array P800

◦ Smart Array P400

◦ Smart Array P400i

◦ Smart Array E200i

◦ Smart Array E200

◦ Smart Array E500

◦ Smart Array P700M

hpsa(4) - Linux man page

Name

hpsa - HP Smart Array SCSI driver

Synopsismodprobe hpsa [ hpsa_allow_any=1 ]

Description

hpsa is a SCSI driver for HP Smart Array RAID controllers.

Optionshpsa_allow_any=1: This option allows the driver to attempt to operate on any HP Smart Array hardware RAID controller, even if it is not explicitly known to the driver. This allows newer hardware to work with older drivers. Typically this is used to allow installation of operating systems from media that predates the RAID controller, though it may also be used to enable

hpsa to drive older controllers that would normally be handled by the

hpsa, and

Supported hardware

The

hpsa driver supports the following Smart Array boards:

Smart Array P700M

Smart Array P212

Smart Array P410

Smart Array P410i

Smart Array P411

Smart Array P812

Smart Array P712m

Smart Array P711m

StorageWorks P1210m

Configuration details

To configure HP Smart Array controllers, use the HP Array Configuration Utility (either

hpacuxe(8) or

hpacucli(8)) or the Offline ROM-based Configuration Utility (ORCA) run from the Smart Array's option ROM at boot time.